2. Lay out the three wreath sections to form a circle. The wreath
section where lights are missing (to later allow for bow
placement) should be at the bottom of the circle. The wreath
section with a capped light string connector should be on the
right side of the circle (Fig 2).
NOTE: Check the item for any loose, unlit or damaged bulbs.
Although it will still operate, the bulbs must be replaced
promptly to ensure the performance and life expectancy of the
item. Also check that the support chains are not tangles and
the lights are hooked onto the frame.
6. To illuminate, fully insert the plug into a working GFCI outlet
or an outdoor rated extension cord.
ASSEMBLY INSTRUCTIONS:
No tools required.
Retain carton for storage.
1. Carefully remove all parts from the carton Your wreath should
include the following (Fig 1):
3 Wreath Sections
1 Bow Section (unfold upon removing from carton)
Replacement LED bulbs and light clips
Fig 6
4. Attach the bow to the wreath section where no lights are
attached, by inserting the hooks on the bow into the metal
sleeves on the wreath section, on each side of the bow (Fig 5).
5. To electrically connect the sections, locate the uncapped
coaxial connectors on each of the sections. Align the male
ends to the female connectors as shown in Fig 6 and connect
them together. Slide the screw cover from the “male”
connector over the “female” connector and tighten.
You have completed the assembly of the wreath.
Fig 1
3 Wreath Sections
Replacement LED bulbs
and light clips
Bow Section
Repeat on next section to form a circle (Fig 4).
Fig 4
Fig 5
Fig 2
3. Connect the 3 wreath sections by inserting each section first
into the metal sleeves on the wire frame and then inserting
the hooks into the eyelets on the wire frame (Fig 3).
Fig 3
LED14
Model No. 7407096UHO
NOTE: DO NOT USE A DIMMER SWITCH OR INSTALL ANY
ADDITIONAL CHRISTMAS LIGHTING OR ORNAMENTATION
THAT IS POWERED BY A LIGHT BULB SOCKET. DOING THIS
MAY RESULT IN DAMAGE TO THIS PRODUCT OR CAUSE
PERSONAL INJURY. THIS ACTION WILL RESULT IN A VOID
OF THE LIMITED WARRANTY OF THIS PRODUCT.
1. Failure to light; unplug the product and check to see that
the GFCI outlet is functioning.
2. A section fails to light; unplug the product and check all
light string connections. This product uses low voltage
coaxial connections. To connect the light strings; align the
male end to the female connectors as shown and connect
them together. Slide the screw cover from the “male”
connector over the “female” connector and tighten (Fig 6).
TROUBLESHOOTING
1. Leave assembled if storage room permits or disassemble,
placing all components in the original carton.
2. Store in cool, dry location away from sunlight.
CARE AND CLEANING
This outdoor wreath sculpture includes replacement bulbs
for any replacements that you need to perform on your
sculpture. If extra parts are needed, contact the Customer
Service Team at 1-877-527-0313.
MAINTENANCE
Made in China
Printed in China
This is not a toy, for decorative use only.
This product was pre-tested before shipment and date
coded. In keeping with the National Electric Code, this
product is intended for seasonal (90 days max.) installation
and use. For problems or questions on this product call
Home Depot customer service toll-free at 1-877-527-0313.
DISTRIBUTED BY HOME DEPOT U.S.A., INC. 2455
PACES FERRY RD., N.W. Atlanta, GA 30339 All rights reserved.
11.5”
2014 THD.com
Outdoor Wreath Sculpture Instruction Sheet (English)
Date: 4/7/14
11.5”
(2 pages)
(1 pages)
(1 pages)
(6 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals