Fig 10
NOTE: DO NOT USE A DIMMER SWITCH OR INSTALL ANY
ADDITIONAL CHRISTMAS LIGHTING OR ORNAMENTATION
THAT IS POWERED BY A LIGHT BULB SOCKET. DOING THIS
MAY RESULT IN DAMAGE TO THIS PRODUCT OR CAUSE
PERSONAL INJURY. THIS ACTION WILL RESULT IN A VOID OF
THE LIMITED WARRANTY OF THIS PRODUCT.
This outdoor 3D silhouette tree sculpture includes
replacement bulbs for any replacements that you need to
perform on your sculpture. If extra parts are needed,
contact the Customer Service Team at 1-877-527-0313.
MAINTENANCE
Model No. 7407169UHO1
LED14
Made in China
Printed in China
This is not a toy, for decorative use only.
DISTRIBUTED BY HOME DEPOT U.S.A., INC. 2455
PACES FERRY RD., N.W. Atlanta, GA 30339 All rights reserved.
1. Failure to light; unplug the product and check to see that
the GFCI outlet is functioning.
2. A section fails to light; unplug the product and check all
light string connections. This product uses low voltage
coaxial connections. To connect the light strings; align the
male end to the female connectors as shown and connect
them together. Slide the screw cover from the “male”
connector over the “female” connector and tighten (Fig 10).
TROUBLESHOOTING
1. Leave assembled if storage room permits or disassemble,
placing all components in the original carton.
2. Store in cool, dry location away from sunlight.
CARE AND CLEANING
2. Determine the final display location before assembling the tree.
The tree must be placed on level ground. Place the tree base in
the desired location.
3. Insert pole “A” into the tree base. (Fig 2)
4. Insert pole “B” into pole “A” making sure the tab on pole “B” slides
into pole “A” (Fig 3a).
5. Insert pole “C” into pole “B” making sure the tab on pole “C”
slides into pole “B” (Fig 3b).
ASSEMBLY INSTRUCTIONS:
A step stool or ladder maybe needed.
2 people recommended for assembly.
Retain carton for storage.
1. Carefully remove all parts from the carton. Your tree should include
the following (Fig 1):
1 tree base
5 collapsible tree panel section
1 bottom support pole (A)
1 middle support pole (B)
1 top support pole (C)
1 spire
4 Lawn stakes
Replacement LED bulbs and light clips
Fig 1
Tree base
Collapsible
tree panel
section
Replacement
LED bulbs and
light clips
Support poles
Spire
Lawn stakes
Fig 9
6. Separate each panel unfolding all 5 panels (Fig 4 a, b, c).
NOTE: The tree’s 5 panels will be electrically connected by
male and female coaxial connections (Fig 9). The base of the
tree will have (2) of these coaxial connection points labeled #2
and #4. The top of the tree will also have (2) coaxial connection
points labeled #1 and #3.
NOTE: It is important that
when hanging each
individual panel unto the
center support pole that
the two (#2) labeled
pairings of the panels are
together, as well as the (#4)
labeled pairings of the
panels are together, in
order to make the proper
connection points. (The 5th
panel will have no
numbered label; as it
possesses the trees plug).
13. Push the wire stakes into the ground securing the tree
base. Angle each stake 45 degrees toward the center of
the tree (Fig 9).
You have completed the assembly of the tree.
NOTE: Check the item for any loose, unlit or damaged
bulbs. Although it will still operate, the bulbs must be
replaced promptly to ensure the performance and life
expectancy of the item.
14. To illuminate fully insert the plug into a working GFCI
outlet or an outdoor rated extension cord.
This product was pre-tested before shipment and date
coded. In keeping with the National Electric Code, this
product is intended for seasonal (90 days max.) installation
and use. For problems or questions on this product call
Home Depot customer service toll-free at 1-877-527-0313.
A
Fig 2
Fig 4a
10. Proceed to make the (4)
necessary male and female
connections in order to
electronically connect the tree
panels.
11. Place the spire on top of the
tree. (Fig 8)
12. Proceed to take the loose string
of lights located at the top of
one of the tree’s panels and
begin wrapping and clipping
the light string to the spire.
Fig 4b Fig 4c
Fig 6
Fig 7
7. Take the 1st panel, (that
possesses the trees plug), and
starting from the top of the
pole to the bottom insert the 4
prongs into the 4
corresponding eyelets (Fig 5).
8. Proceed in hanging the
remaining 4 panels in the same
manner as the above; noting
that the lower pane pairings of
#2 to #2 and #4 to #4 must be
aligned next to each other (Fig
6).
9. Secure the positioning of each
panel by sliding the base of
each panel into the slots
provided on the top of the
trees base (Fig 7).
Fig 5
Fig 8
B
A
Fig 3a
C
B
Fig 3b
15”
2014 THD.com
3D Silhouette Tree Instruction Sheet (English)
Date: 4/15/14
11.5”
(1 pages)
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals